Edge metal
Every penetration and edge is sealed to keep water out.
Flat Roofing
Rubber Roof Installation Orange, NJ
A roofer in Orange can install a rubber roof by laying EPDM membrane in wide sheets over insulation and a cover board, bonding or fastening it down and sealing every seam with primer and tape, so the roof handles sun, cold and storms for decades. One call to (973) 858-1825 reaches a nearby rubber roof installer.
Rubber roofing usually means EPDM, though some people use the term for any single-ply membrane. EPDM is sold in wide rolls, typically 45 or 60 mil thick, and it stretches and recovers as the roof moves through hot and cold seasons. That flexibility is why it suits so many homes.
EPDM can be attached in three main ways. Fully adhered roofs bond the whole sheet to the cover board with adhesive, mechanically attached roofs use plates and fasteners along the seams and ballasted roofs hold a loose sheet down with river stone. Residential roofs are most often fully adhered.
Then comes thickness and color. A 60 mil sheet is tougher than 45 mil for roofs that see foot traffic. Black is standard and holds heat, while white reflects it. The installer also plans how the membrane laps under shingles above it and up the wall beside it, where leaks tend to start.
If the problem goes deeper than it first looked, an Orange roofer may also recommend rubber roof repair or flat roof installation.
Looking for Orange rubber roof installation? Call (973) 858-1825 to talk to a local roofer.
Call nowThe process
What happens during a rubber roof installation
A rubber roof is built in layers, with the seams and flashing as the critical details.
Prepare the deck
The roofer checks the deck for rot, gaps and loose sheets and confirms the roof has enough slope to drain. A tear-off comes first on existing roofs.
Install insulation
Polyiso insulation and a cover board create a flat, firm base for the rubber. Low spots can be corrected with tapered insulation.
Roll out the membrane
The membrane is unrolled, aligned and allowed to settle before bonding. Seams are planned so they run with the slope.
Apply adhesive
Half the sheet is folded back, adhesive is applied to both surfaces and the rubber is pressed into place. Then the other half is done the same way. Any trapped air is worked out so the sheet lies flat and does not blister.
Tape the laps
Primer and seam tape join the sheets, with T-joints covered by extra patches. Tape edges are finished with lap sealant.
Finish the edges
Perimeter edge metal, wall flashing and pipe boots complete the roof. The top edge is sealed and covered. A final walk checks every seam with a probe before the job is closed out.
What is included
Parts of a new EPDM roof
Seam tape
Every seam gets primer and tape with lap sealant at the edges.
Deck preparation
Decking is inspected and replaced where needed so the roof sits on solid wood.
Rubber sheet
A 45 or 60 mil EPDM sheet is installed with as few seams as possible.
Insulation
Rigid insulation and a cover board form the base and gives the adhesive a firm grip.
Related service
EPDM Roof Installation Orange, NJ
The quality of an EPDM installation shows up years later in the seams and edges. A flat, dry base, properly timed adhesive and carefully primed seams are what make EPDM last. Dry, mild days give the best bond. The field and the flashings may get different adhesives, since vertical surfaces need a stronger grip.
For an Orange home, the installer thinks ahead to how the roof will behave over the years. Flashing at walls and curbs is secured with termination bar so the sheet cannot pull loose as it ages, and corners get flexible uncured flashing. Ask about edge securement before work starts.
Local help
Rubber Roof Installation Near Me
In Orange, EPDM is a popular choice for low slope roofs on additions and attached garages. Across Orange and nearby towns like East Orange, Glen Ridge, Caldwell and Roseland, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, so installation details matter as much as the material.
For rubber roof installation in Orange, NJ or nearby towns like East Orange, Glen Ridge, Caldwell and Roseland, call (973) 858-1825 to reach a roofer who covers your street.
How the weather here affects roofs around Orange
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Orange is busiest after a hard winter and before the next one.
Why call
Why not wait
Drier ceilings
Small roof problems caught early usually stay small repairs.
Familiar with local homes
Local roofers see the same roofs and storm damage across Orange and nearby towns.
Know what happens next
Ask your questions before you agree to anything.
Rubber Roof Installation FAQ
Which EPDM thickness should I choose?
The common choices are 45 mil and 60 mil. Thicker 60 mil is tougher and longer lasting. Heavy duty options exist too.
Is a rubber roof the same as TPO?
The two are different materials. EPDM uses taped seams and stays flexible in cold, and TPO uses welded seams and reflects heat. Each suits different roofs.
Is it possible to install EPDM over the old roof?
EPDM can sometimes go over an existing roof. Codes generally allow one recover over a dry, sound roof. Wet insulation or multiple layers mean a tear-off. Core samples or a moisture scan show whether the old roof is dry enough.
How long does a new rubber roof last?
Rubber roofs often last decades. Thickness, seam quality and maintenance all affect its life. Repairs are simple when needed.
Should my rubber roof be black or white?
The choice depends on the climate and the space below. White helps in sunny climates, and black is common where winters are long. Talk through the choice with a roofer.
More questions? Call (973) 858-1825
Often needed together
Rubber Roof Repair
Repairs for leaking rubber roofs, from peeling seams to pulled flashing at walls and curbs, after the real leak point is found.
Learn moreFlat Roof Installation
New flat roofs built with real slope, insulation, a cover board and a membrane suited to the building, planned around how the roof will be used.
Learn moreTPO Roofing
Heat-welded TPO membrane for flat and low-slope roofs, sized to the deck, the drains and the way the roof is used.
Learn moreFlat Roof Replacement
Replacing old built-up, torch-down, EPDM or TPO roofs with a new system built to drain, and new flashing at every wall, curb and drain.
Learn more
Looking for something else?
See all roofing servicesGet rubber roof installation help in Orange
Call now for Orange rubber roof installation and help in the towns around it.